Need some asistance


	FORUM HOME	SEARCH POSTS	WHO'S ONLINE	LOG IN	RULES F.A.Q.

TV Forums: TV Equipment: TV Repair Forum:
Need some asistance

Print Thread

johnedog555
New User

Aug 30, 2010, 1:14 AM

Post #1 of 9 (824 views)
Shortcut

Need some asistance	Can't Post

Hello there recently I have switched cable services and so I unplugged the boxes and such to return to the store. On my return home I find that the part where my cable wire goes into had the copper piece from my splitter stuck in it. This is of course a issue since the other copper wire cannot go into the tv. My first instinct would be to remove the back of the tv and do this, however this is a good tv and I would not want to have a accident. So any advice or tips or instructions would be great.

jts1957
Veteran

Aug 30, 2010, 1:46 AM

Post #2 of 9 (818 views)
Shortcut

Re: [johnedog555] Need some asistance [In reply to]	Can't Post

Small sewing needle?

-------------------------
Location: Far, Far Away

johnedog555
New User

Aug 30, 2010, 8:59 PM

Post #3 of 9 (811 views)
Shortcut

Re: [jts1957] Need some asistance [In reply to]	Can't Post

unfortunately a small needle did not work, I have removed the back of my television as a hope it would come out better through the back but I dont see a way to remove the piece of wire.

jts1957
Veteran

Aug 31, 2010, 12:44 AM

Post #4 of 9 (806 views)
Shortcut

Re: [johnedog555] Need some asistance [In reply to]	Can't Post

New Tuner.

-------------------------
Location: Far, Far Away

johnedog555
New User

Aug 31, 2010, 1:29 AM

Post #5 of 9 (804 views)
Shortcut

Re: [jts1957] Need some asistance [In reply to]	Can't Post

are these easy to come buy and easy to install, sorry for so many questions its just a expensive tv and all.

jts1957
Veteran

Aug 31, 2010, 2:24 AM

Post #6 of 9 (803 views)
Shortcut

Re: [johnedog555] Need some asistance [In reply to]	Can't Post

I can't say since you don't say. Crazy

-------------------------
Location: Far, Far Away

darstr
User

Sep 1, 2010, 8:51 PM

Post #7 of 9 (792 views)
Shortcut

Re: [johnedog555] Need some asistance [In reply to]	Can't Post

Tuners don't pose to much of a problem to change, but be weary that it might be on a double sidded board. That can make it a bear to get all the little pins out. Some chip quick and a solder sucker should do the trick though.

johnedog555
New User

Sep 2, 2010, 2:33 AM

Post #8 of 9 (789 views)
Shortcut

Re: [darstr] Need some asistance [In reply to]	Can't Post

Alright so lets say this is a single pin tuner would I would I need the tools you listed or is that only for multi sided tuners?

darstr
User

Sep 2, 2010, 11:26 AM

Post #9 of 9 (786 views)
Shortcut

Re: [johnedog555] Need some asistance [In reply to]	Can't Post

I didn't say anything about t 2 sided tuner. They don't even exist I don't think. I am refurring to the board the tuner is soldered on to. But yes, those are basic accy's needed for board repair.

Print Thread

Search for (options)

- Page loaded in: 0.14 s on (CGI/1.1)